9 Simple Steps to Waterproofing Exterior Walls

Your walls form the foundation of your home. You need to pay special attention to the exterior walls of your house because the weather out there will not be nice. It is not enough to paint the wall. After dealing with rain, snow, wind, dust and heat of the outside environment, the paint will start peeling off.

Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.

Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.

Step 1: Properly expose the outside part of the wall

To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.

Step 2: Thoroughly clean the walls

“The outer part of your home’s wall is usually covered with a lot of dust and dirt that sticks to it. To ensure the efficiency of the entire process, you need to clear off the debris and dust thoroughly. The dirt and debris can be cleaned by using a broom, brush, or sandpaper. You can finish it off with a power washer.”

Step 3: Check out for the cracks and fill them up

Cracks and holes can develop on your walls over time. Follow up the cleaning process with a thorough look at the cracks and holes on your wall. They should be filled up with cement.

Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.

All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.

The cement mixture can penetrate inside the cracks. Make sure to remove the loose cement from the wall before applying the cement.

Step 4: Add a layer of cement waterproofing sealer

If you want to make sure your wall is waterproof, you need to apply a cement waterproofer. After applying the cement in the crevices, let it dry and then apply the waterproof paint sealer. Allow it to be dry.

Step 5: Pick the right water-proofer

“There are a lot of waterproof products in the market. It’s important to pick the right one for your wall. Pick the water-proofer based on whether the wall is concrete or silicate.”

You can choose between a silicate-based concrete sealer and a concrete waterproof coating. Pick a plaster waterproof Additive to strengthen your walls.

Step 6: Apply the water-proofer

Apply the water-proofer with a roller or brush on the walls. If you want to apply more than one layer, give a thin coat initially. Add the second coating after the first one has dried.

Step 7: Apply tar and heavy-duty membrane

If you want to add more strength to the layer, you need to use a tar-based pitch. You can apply it on the wall.

After that, you need to apply a heavy-duty plastic or rubber membrane, which will ensure the proper care of your wall.

Step 8: Consider adding gravel

To lay the drainage pipes, you need a base below the footer. The drainage pipes will get adequate support from the gravel base. Gravel provides enhanced protection and is long- lasting.

You need to lay the drainage pipe-cover and gravel. To back-fill the gravel, level it near the footer. A covering for the pipe should be at least 3-inches.

Step 9: Add a fabric barrier

The fabric barrier should be secured along with the pipe. Ensuring a fabric barrier is going to keep dirt out of your system. Simply back-fill the trench and build the top of the dirt relatively high and allow it to settle for a while. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia is

Conclusion:

“Your home gets a new life and strength when it’s waterproof. Magicrete can help you with waterproof solutions for your walls. At a very low and affordable price, Magicrete offers you proper weatherproofing with quality service.”

“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s”